Parts of a Screwdriver and How Each Tip Type Fits

Julian Mercer
10 Min Read

The parts of a screwdriver are a handle, a shank, and a tip. The handle is gripped and turned, the shank is the steel rod, and the tip fits the head of the screw. A ferrule, a bolster, or a grip is added on some models.

A manual screwdriver runs from the tip to the handle. The flathead, Phillips, and ratchet types change the tip or the handle. An electric or cordless driver is a powered tool, and a drill houses a motor, a chuck, and a trigger. The hammer and pliers are two other hand tools.

Parts of a Screwdriver Labeled Diagram

Parts of a screwdriver showing the handle, shank, shaft, bolster, and tip designed to engage a screw head
Screwdriver components transfer hand force to turn screws.
Advertisement

In a labeled diagram of a screwdriver, the tip is at the front and the shank extends back from it. The handle is at the rear. Every part of a screwdriver belongs to the tip end, the shank, or the handle.

PartWhere you find it
1. TipWorking end of the shank that fits the screw head, also called the head or the blade
2. ShankSteel rod between the tip and the handle, also called the shaft
3. BolsterHex collar near the handle that a wrench grips
4. FerruleMetal collar where the shank enters the handle
5. HandleGripped part at the rear end of the screwdriver
6. GripRubber or soft covering on the handle
7. CapEnd piece of a precision screwdriver that spins in the palm
Screwdriver tip types including slotted, Phillips, Pozidriv, Torx, hex, Robertson, tri wing, security Torx, and spanner profiles
Screwdriver tips match specific screw recess shapes and sizes.

How Many Parts a Screwdriver Has

A standard screwdriver has three parts: the handle, the shank, and the tip. Each part has its own job. The handle takes the hand, the shank transfers the turning force, and the tip engages the screw. The knife is another hand tool with a working end fixed in a handle.

Counts of four to seven add the ferrule, the bolster, the grip, and the cap. These parts are fitted to some models only, so three is the count that fits every manual screwdriver.

Screwdriver Handle Parts

The handle is the widest of the parts of a screwdriver, shaped to fit the hand. It is made of wood, metal, or plastic, and composite handles combine rigid plastic with rubber.

Handle Shape

Handles are hexagonal, square, or oval in profile. A cabinetmaker’s handle is roughly oval, and modern plastic handles are roughly hexagonal.

Grip

The grip is the rubber or soft covering on the handle. It improves the hold and adds comfort. Not every handle has one.

Cap

The cap is the end piece of a precision screwdriver. It lets the handle spin freely in the palm while the fingers turn the shank.

Screwdriver Shank Parts

Among the parts of a screwdriver, the shank is the thinner length between the handle and the tip. It is round or hexagonal and made of tough steel, which resists bending and twisting.

Shank

The shank transfers the turning force from the handle to the tip. It measures about 1/3 inch thick and from a few inches to over a foot long.

Bolster

The bolster is a short hexagonal collar near the handle. A wrench grips it to add torque when the hand alone falls short.

Ferrule

The ferrule is a metal collar at the junction of the shank and the handle. It reinforces the neck of the handle.

Types of screwdrivers including flathead, Phillips, Pozidriv, Torx, hex, Robertson, tri wing, precision, and ratcheting designs
Screwdriver types match different screw heads and fastening tasks.

Parts of a Flathead Screwdriver

The parts of a flathead screwdriver are the flat blade tip, the shank, and the handle. The slotted tip is also called the flat-blade or common-blade tip. It fits a single straight slot.

The slotted tip is prone to slipping out of the slot under power. Better blades are induction-hardened or coated with black oxide. The tip width is measured in millimeters or inches, such as 3/16 inch.

Parts of a Phillips Screwdriver

The parts of a Phillips screwdriver are the cross tip, the shank, and the handle. The tip is a cross shape with a 57 degree point. Sizes run from #000 to #4.

A tip of #1 or smaller has a blunt point, and a tip of #2 or larger is nearly squared off.

Other Screwdriver Tip Parts

The tip is the part among the parts of a screwdriver that differs most between types. Its shape is matched to the drive of the screw head.

Pozidriv Tip

The Pozidriv tip is a cross shape with parallel flanks and ribs at 45 degrees. It is an improvement on the Phillips tip.

Robertson Tip

The Robertson tip is a square tip with a taper that retains the screw. Sizes run from 1.77 mm to 4.85 mm.

Torx Tip

The Torx tip is a six-lobed star that fits a hexalobular socket. Sizes run from T5 to T40.

Hex and Security Tips

The hex tip fits a hexagonal socket. Pentalobe and other security tips fit tamper-resistant screws.

Magnetic Tip

A magnetic tip is magnetized to retain ferromagnetic screws, which helps with small screws and in confined spaces.

Parts of a Screwdriver Bit

A screwdriver bit is a replaceable tip. The parts of a screwdriver bit are the drive tip and the shank end, which fits the driver. A multi-bit screwdriver stores several bits in one handle.

Parts of a Ratchet Screwdriver

The parts of a ratchet screwdriver are the tip, the shank, the ratchet mechanism, and the handle. The mechanism locks the blade to the handle in one direction of rotation and releases it in the other. A switch sets the direction.

A multi-bit ratchet driver uses a reversible ratchet. It allows several full turns without repositioning the hand on the handle.

Yankee Driver

A Yankee driver, also called a spiral ratchet driver, converts a push on the handle into rotation. A pawl runs in a spiral groove inside the shank.

Offset and Precision Screwdriver Parts

An offset screwdriver has the handle set at a right angle to a small blade. It reaches narrow spaces and adds torque.

A precision screwdriver is small, and its cap lets the handle spin in the palm.

Screwdriver Parts and Their Materials

The materials of the parts of a screwdriver are steel for the shank and the tip, and wood, metal, or plastic for the handle.

Steel: The shank is tough steel. The tip is hardened to resist wear, and it is coated dark for contrast with the screw or ridged for grip on some drivers.

Handle materials: Wood is the traditional material. Plastic and composite handles with rubber are modern.

Grip: The grip is rubber or a soft plastic.

FAQs

FAQs

Q1. What are the parts of a screwdriver called?

The parts of a screwdriver are the handle, the shank, and the tip. A ferrule, a bolster, a grip, and a cap complete the parts on some models.

Q2. What are the three parts of a screwdriver?

The three parts of a screwdriver are the handle, the shank, and the tip. The handle is gripped and turned, the shank is the steel rod, and the tip fits the screw head.

Q3. Does a screwdriver have a head?

Yes, the tip of a screwdriver is also called the head. It is the end of the shank that fits into the screw head, and it is hardened more than the shank.

Q4. Why are screwdrivers shaped the way they are?

Each part has a shape that matches its job. The handle is wide for the hand. The shank is thin to reach a recess, and the tip matches the drive of the screw.

Q5. What do the parts of a screwdriver do?

The handle takes the hand, and the shank transfers the turning force. The tip engages the screw, and the ferrule and the bolster reinforce the junction of the shank and the handle.

Related:

Advertisement
Share This Article
Follow:
I'm Julian Mercer, founder of Englishan.com and an English educator with more than a decade of teaching experience. I hold a master's in Applied Linguistics, with expertise across grammar and vocabulary and a specialization in visual vocabulary. I'm particularly fascinated by the relationship between imagery, language, and word recall.